IBM BladeCenter S - getting started with Blades in the SMB Market

Last Friday i received a new toy. An IBM BladeCenter S, with two HS21, one HS21 XM and a JS12 Blade.

The BladeCenter S

The BladeCenter S i received came with 10 500GB SATA Disks and two DSMs, four power supplies, an Advanced Management Module, a Server Connectivity Module and a SAS Connectivity Module. The power supplies use standard 230V type 23 plugs, which do require a little special installation, but much less so than industrial plugs used with the bigger BladeCenters.

The big point about the BladeCenter S is that it does not require an external SAN to provide Storage to the Blade - an integrated SAS Switch that allows very flexible disk configurations is integrated. Configuration can be done using a Webbrowser against the SAS Connectivity Web Interface, using SSH/Telnet to access the SAS Connectivity Commandline, or using a fully graphical interface using IBM’s Storage Configuration Manager. There are some predefined configurations, but none of them suited my configuration - creating new configurations using SCM is easy enough though.

The disks in the BladeCenter’s DSMs (Disk Storage Module) are hot swappable - currently, only 3.5″ DSMs are available, with a 2.5″ DSM in the pipeline. Most of the blades support one or two internal disks, but the problem here is that these disks are not hot swappable. Depending on your Blade loadout, 12 disks might not be enough. For example, the HS21 XM Blades only fit one internal disk, and running without RAID on the System partition seems pointless, so you would be using at least 6 disks (without hotspares) for a basic Exchange deployment.

The Webinterface on the AMM is nicely done, although it lacks a bit of flashiness. That’s not a requirement though, it does a very solid job at what it needs to do.

After powering up the BladeCenter S for the first time, i connected to it using a web browser and upgraded all the firmwares. There are quite a lot of them (AMM, SAS, Server Connectivity), but it all worked out flawlessly. Time to move on to the real course: the Blades.

The HS21 and the HS21 XM

Starting with the familiar first, i started with the HS21 Intel Blades first. The two HS21 Blades both had a 2.66 Ghz Quadcore and 4GB RAM, the HS21 XM Blade had a 2.5 Ghz Quadcore and 9GB of RAM (more about that later).

When starting the first HS21 Blade, after configuring all the storage using SCM, it failed to POST it’s LSI Logic SAS/RAID Controller. I searched for the error message on the net, assuming that i screwed up the configuration. I didn’t find anything meaningful, so i tried to do what everyone else would do in this situation: Apply every Firmware update for the Blade i could find.

Of course it wasn’t as easy as i wanted it to be. The controller not POSTing was an endless loop, i couldn’t get the machine to start from the AMM virtual floppy drive. I used SCM to disconnect the storage (by disabling the Blade’s SAS port). Now, the blade booted flawlessly, indicating that i probably had a problem with my disks. When browsing the IBM website, it became obvious that only newer firmwares support SATA drives. After upgrading the SAS Firmware, i was able to boot the blade without disabling the Blade’s SAS port. Unfortunately, the onboard SAS controller only supports RAID level 1 and 10. Probably owed to the fact that most blades are using SAN storage - IBM promised that there would be SAS RAID adapter that supports other RAID levels - these are especially important for the cost-conscious SMB market.

I booted a Windows PE 2.0 using WDS, and was able to install Windows Server 2008 x64 without any issues.

The HS21 XM blade on the other hand complained when booted for the first time that it’s memory configuration was invalid - it only supports 2, 4 and 8 DIMM configurations - 6 DIMM configurations are not supported. I removed two 512MB modules and booted the Blade with 8GB - it worked flawlessly and without complaining.

The JS12

First, read this document about i on Blade. It explains everything better than i ever could.

The JS12 is a POWER6 based blade that is able to run IBM i. The first time i turned on the blade, all the HS21 blades (already running Windows Server 2008) crashed hard. When rebooting, they no longer found their drives. I turned off all the blades, disconnected the JS12’s SAS port and turned everything on again. The Intel blades booted, and after i was sure that they’re up and running again, i powered on the JS12 again. This time, no issue arised. I tried to reproduce the behaviour i’ve seen before, and the same thing happened again.

My current assumption is that the issues were caused by the SAS Controller which does not have a Firmware update yet, and can’t deal with the SATA drives located in the DSMs. Further investigation told me that there’s no firmware upgrade for the SAS Controller in the POWER6 blade, and that SATA drives are not supported when running IBM i on the blade anyway. I ordered 4 147GB SAS drives, disabled the SAS port on the blade, and tried booting the POWER6 blade again. It booted flawlessly again.

The next step was to install VIOS - this is a rather complicated multi-step process. First, you have to turn on “Serial over LAN” aka SOL, then logon to the AMM using SSH, connect to the POWER blade using serial passthrough and then boot the blade from the VIOS CD. The install is pretty self explanatory.

Next is connecting to the Integrated Virtualization Manager (IVM) running on the VIOS partition. The IVM is basically a HMC light minus the console functionality. The only way to get a console on the JS12 blade is using a LAN console (which can only run on consumer versions of Windows, and is not supported on most of the Blades).

I installed the latest VIOS patches (around 4GB) and enabled mirroring on the two 147GB SAS disks in the blade itself. The next step will be installing IBM i, with which i have to wait until i receive the ordered SAS Disks.

Preliminary Summary

The BladeCenter S is great. Yep, not everything ran flawlessly from the start, but nobody’s perfect from the beginning. The BladeCenter brings an innovative new perspective to the SMB market. The problems that IBM needs to address are the addition of 2.5″ DSMs (already in the works) and more capable RAID controllers (also in the works). A BladeCenter S with the ability to use around 20-40 disks could prove interesting.

The POWER6 Blade is interesting, and while VIOS adds complexity, it is as streamlined as possible. I’m interested about seeing IBM i running on the machine.

If you have any other question about the BladeCenter S - or anything you would like to see in detail, post a comment. I’ll try to figure it out.